iopsustainable.blogg.se

1. #Hyper 212 evo install on lga 1155 full
2. #Hyper 212 evo install on lga 1155 pro
3. #Hyper 212 evo install on lga 1155 windows

The highest i have seen it was doing stress tests and it hit 48 during an hour of stress on it with Prime95 etc.

#Hyper 212 evo install on lga 1155 full

TEMPS - Again WOW - idle is between 10-18, light load 20-25ish, full load it has only got to 37. This is with the case open on my desk and sitting on top of it. Everyone in the house couldn't believe it was even on. So checking stock heatsink / fan first - and I could not be happier !!!!!!ġ.

#Hyper 212 evo install on lga 1155 windows

:( - Started checking in windows and idle was 60+ if i would start any game at all it might get to title screen or shortly after and either blue screen or just reboot. cpu temp was in 60's almost 70, on cold boot in bios. Turned it off overnight and the next day booted it and straight into bios. Pros: My 8350 was on stock for the last 3 yrs without any issues and suddenly blue screens and reboots all over the place and I have not done any OC'ing with it at all. Twin 120mm Corsair MagLev Exhaust Case Fans (75% PWM Mobo) Twin 120mm Corsair MagLev Intake Case Fans (75% PWM Mobo)

#Hyper 212 evo install on lga 1155 pro

Samsung 960 Pro 1TB M2 SSD Benchmarked 29.5 MB/s Sequential Read (O/S & Game Library Drive) EVGA GTX 1080 FTW2 Running Dual 27" Monitors 32GB DDR4 Dual Channel Corsair RAM 2666Mhz Frequency Arctic Silver 5 High Density Thermal Paste Cryorig H7 Heat Sink w/ Dual Corsair 120mm MagLev Fans (Mobo Curved on Push-Pull Config) I hope this helps someone get better performance out of their H7. A circular spread will never entirely cover a square surface, thus not utilizing the entire IHS to dissipate heat. The thermal paste is used to fill in air gaps between the heat sink(liquid or air) and processor due to a non true or an imperfectly flat surface on both the heat sink contact surface and processor IHS. You cannot cover the entire IHS end to end with a pea sized dot applied to the center of the IHS. I have done it this way since 2001 and have seen better results in many cases. I continue to spread in a criss-cross pattern until the entire surface is completely covered with a very thin layer of thermal paste. I use a straight razor and apply even pressure as I use it as a spreader to spread the paste across the entire surface of the IHS. I use a small amount, applying it across one end of the IHS, from one corner to the other side-corner. I used Arctic Silver 5 High Density thermal paste. This was unexpected due to all of the rumors about temp spikes people have been posting on the internet about the i7 7700K. I noticed that while playing games like Rise of the Tomb Raider, Squad, Elite Dangerous, Scrap Mechanic, ME Andromeda, The Division, The Witcher 3, Etc. It's nice that these tower heat sinks come with enough hardware to mount two fans. I used 2 Corsair 120mm MagLev fans (Mobo Curved on a push - pull config) to keep my 7700K cool. It's the reason I gave it 4 out of 5 eggs. I have received other products this way even though they are listed new.

I can usually tell when a box has been opened by seeing that either it has no seal or the seal has been tampered with. 2 fins were bent & there was still dust in the fins and on the fan.

I was a bit irritated that I received a used product. Overall Review: I have no issues with this being used, because the contact base was flawless and I did not use the fan that came with it.